Skip to main content

Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit

Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit



Description:

The purpose of the experiment:
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;

Experimental steps:

Step 1: The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2: In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3: Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4: Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5: Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6: Know the self-locking. Press and wait for the light to be on, then press the light to turn off.

Package included:

1 x DIY LED Dimming Lights Technology Small Production Kit















Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit See detail


Popular posts from this blog

BGA152 BGA132 BGA136 TSOP48 NAND Flash USB 3.0 U Disk PCB IS917 Main Controller Without Flash Memory for Recycle SSD Flash Chips

Get BGA152 BGA132 BGA136 TSOP48 NAND Flash USB 3.0 U Disk PCB IS917 Main Controller Without Flash Memory for Recycle SSD Flash Chips null Please download software here: IS917     Specifications: Main Controller IC : IS917  USB type: USB3.0  PCB size:14*33mm(without the USB port size) Support IC: BGA152/132/136 TOP48 (two solder chips,every chips need 2CE.But if you weld one chip in PCB,MAX 4CE)  Usage:(USB3.0 interface High speed) NAND flash R/W Strick  Can be delete all partition  Can be Read & Write   Q&A: 1. support those chips? Except the latest UFS2.0 chip, other conventional chips are supported; 2. USB2.0 and USB3.0 U disk difference?  USB2.0 slow, only support single-sided paste, 3.0 speed fast, support double-sided paste, the current only BGA152/132/136 TOP48; 3. Why my chip after welding, no display, detection voltage is zero red light?  May be the problem, one is the chip is broken; two may be welding is not good, there is t...

YL160 4-in-1 Magnetic Stripe Credit Card EMV IC Chip RFID PSAM Card Reader Writer Duplicator

Get YL160 4-in-1 Magnetic Stripe Credit Card EMV IC Chip RFID PSAM Card Reader Writer Duplicator Features : POST, USB powered Compatible with EMV4.3/PBOC3.0 specification support multi-functional PSAM operation LED light prompt data transmission process .Long Service Life Magnetic Head Support the function of the SAM card operation Use USB to communication with PC Thin, light, beautiful, practical Support magnetic /IC chips /13.56mhz RFID NFC /PSAM cards USB interface, plug and play, no need to install additional drivers USB interface, truly plug and play, no need to install drivers Read magnetic cards, IC card reader, proximity card function Reading the full three-track magnetic card, support bi-directional swipe Provide many development platform interface function and application example Support Windows 7, Windows 8, Win2008, Windows 2003, Windows 2000, XP, Linux, etc Can read&write a variety of memory card and supports T...

3pcs 48*LED 850nm Illuminator IR Infrared Light Board Night Vision for CCTV Camera 12V DC

Get 3pcs 48*LED 850nm Illuminator IR Infrared Light Board Night Vision for CCTV Camera 12V DC Features:   - Infrared illuminator board for CCTV security cameras - Replace a camera LED board for your broken or worn out IR LED board - Bright infrared LEDs without much energy consume - Suitable for camera shell of 50mm diameter - Number of IR Lamp:   850nm   48 LED F5 (F5: LED bulb diameter: 5mm) - Voltage: 12V DC - Board Diameter: 53mm    Package Included:   3 x 48*LED 850nm Illuminator IR Infrared Light Board 3pcs 48*LED 850nm Illuminator IR Infrared Light Board Night Vision for CCTV Camera 12V DC See detail